|
Sketch Dec 3
|
Checking the float level 2
|
I must have made a dozen of
these sketches, but this one is
based on a picture of the bike
as it ...
All rights reserved
Uploaded on Dec 3, 2009
4 notes /
0 comments
|
With the float chamber removed
and a hose connected to the fuel
inlet. I am blowing in the hose
and ...
All rights reserved
Uploaded on Aug 20, 2009
1 note /
0 comments
|
|
Checking the float level 1
|
Carb still leaking
|
Step one, see how high it
floats. A little less than half
of it is under water.
All rights reserved
Uploaded on Aug 20, 2009
1 note /
0 comments
|
One step forward and three steps
back. The bike is put together
again, the battery is fully
charged, ...
All rights reserved
Uploaded on Aug 15, 2009
1 note /
0 comments
|
|
Bike almost put together again 2
|
Bike almost put together again 1
|
The bike got put together again
after months of carb cleaning
and searching for faults. The
battery ...
All rights reserved
Uploaded on Aug 9, 2009
0 comments
|
The bike got put together again
after months of carb cleaning
and searching for faults. The
battery ...
All rights reserved
Uploaded on Aug 9, 2009
4 notes /
0 comments
|
|
Excess springs, bad
|
Barbour International Jacket
|
I found these two springs laying
around after I had put the
carburetor and petcock back
togheter and ...
All rights reserved
Uploaded on Jul 8, 2009
0 comments
|
Spent last night rewaxing my
International jacket. Ready for
the riding season! Now if only I
could ...
All rights reserved
Uploaded on Apr 26, 2009
0 comments
|
|
Barbour International Jacket
|
License plate holder, for sale
|
Spent last night rewaxing my
International jacket. Ready for
the riding season! Now if only I
could ...
All rights reserved
Uploaded on Apr 26, 2009
0 comments
|
This one never came to use and
is now for sale, unused.
All rights reserved
Uploaded on Apr 20, 2009
0 comments
|
|
Taillight, for sale
|
Checking the float height
|
This one never came to use and
is now for sale, unused.
All rights reserved
Uploaded on Apr 20, 2009
0 comments
|
The float height is 5-7 mm below
the recomended level, depending
on which manual you are reading.
All rights reserved
Uploaded on Apr 12, 2009
0 comments
|
|
Rig for checking the float height
|
Nice and clean carburetor
|
I built this rig to get the
carburetor leveled so I can
check the float height.
All rights reserved
Uploaded on Apr 12, 2009
2 notes /
0 comments
|
...also trying out the macro
mode on my new Canon Ixus 100
IS. No more crappy mobile phone
pictures ...
All rights reserved
Uploaded on Apr 12, 2009
0 comments
|
|
Nice and clean petcock
|
Biltwelll "Aces" Bars
|
...also trying out the macro
mode on my new Canon Ixus 100
IS. No more crappy mobile phone
pictures ...
All rights reserved
Uploaded on Apr 12, 2009
0 comments
|
There was a recall notice on the
Biltwell Keystone bars I bought
last year, so I asked those ...
All rights reserved
Uploaded on Mar 23, 2009
0 comments
|
|
Petcock Filter
|
Sand found in the petcock
|
A gap between the mesh and the
petcock. Not sure it should be
there?
All rights reserved
Uploaded on Mar 3, 2009
0 comments
|
All rights reserved
Uploaded on Mar 1, 2009
1 note /
0 comments
|
