Botstuff Cleanout Blowout Thing '07

To take full advantage of Flickr, you should use a JavaScript-enabled browser and
install the latest version of the Macromedia Flash Player.

Hitec Laser 4 Tx & charger.
72mHz.

Hitec CG-340 charger and power supply

3"X7/8" and 4"X7/8"
Colson Performas
2 of each size, keyed.

3# combat robot chassis
comes with weapon drivetrain and motor.
mounts for banebots 25mm gearmotors.
14" Ti weapon blade
O-ring transmission
Oilite weapon bearing, precision stainless shoulder bolt axle.
Fireball 19t motor, ~2:1ish ratio

3 Steel sprockets
specs unknown
"35B36H C" and "IEI" on side

Weapon motors.
speed 280
speed 400
speed 550
2 Fireball modified 19Ds(1 missing label)

6 single standard servos
2 standard servos y-cabled together
1 GWS park L servo

3# combat robot weapon blade.
hardened S7 tool steel
3/8" titanium shaft
aluminum hub
hott.

2 Banebots BB-12-45 ESCs

2 12# bot escs
specs unknown

antweight electronics harness
2 scorpion minis
1 brushless Esskay outrunner
1 brushless ESC
JST power connector & microswitch

20:1 modified paper towel dispensor gearmotors; metal spur gears. 5mm output shafts. 3 motors, 2 sheet Al mounts.

banebots 16mm gearhead motors
24:1 ratio
one full gearhead motor, one gearhead.
3mm shaft with flat
metal gears

3 60:1 copals
1 22:1 minimotor, swiss, very nice
all 3mm shafts with flats

handiworks motor, with 5/8" OD adaptor
modified handi with 1/2" out put with large flat

small 3 3/8" carbide-tipped sawblade.

nutter 1# chassis and drivetrain.
gearboxes are 3.33:1 ratio, speed 400s on back, 2" wheels and 4mm shafts
chassis is bent 1/16" lexan and small standoffs.
suggested guts: 3-cell lipo, spektrum .3oz rx, banebots 12# ESCs, and a thwacky tail.

VERY FAST drivetrain. scaling mixer radio suggested.

3# chassis and unhardened tool steel blade, peligro style.
chassis is 1/8" carbon fiber and UHMW
Guts are Tekin rebel, heatsinked scorpion minis, 25mm 20:1 banebots motors.
Guts work with either chassis.

Apogee 3-cell 1050mAh Lipo
10.5C continuous
14C for 5-10 seconds
JST connector

5-cell ant 500mAh pack, NiMH
JST connector

8-cell ant 500mAh pack, NiMH
JST connector

12-cell NiCD
N-500AR cells
radio-style connector

830mAh Apogee Lipo 3-cell
JST connector

6-cell 1400mAh NiCd
Tamiya connector

"Spa Pack"
10-cell
1600mAh
supposedly 60A burst, untested.
recently cycled, ~1550mAh actual.

spare 20:1 25mm banebots gearhead

View vrogy's map

Taken in a place with no name (See more photos or videos here)

Selling the remaining botgear I have.

Hitec Laser 4 Tx and charger
Hitec CG-340 charger and power supply
3 steel sprockets, "35B36H C" "IEI"
speed 280
speed 400
speed 550 "RS550PH"
20:1 25mm banebots gearhead
6 standard servos
2 Y-cabled together standard servos
1 GWS Park L servo
2 3"X7/8" Colson Performas, keyed at 5/8" GONE
2 4"X7/8" Colson Performas, keyed at 5/8" GONE
Apogee 3-cell 1050mAh pack, 14C burst, JST connector
1 Apogee 3-cell 830mAh packs, JST connector
1 5-cell 500mAh NiMH, JST connector
1 8-cell 500mAh NiMH, JST connector
1 10-cell N-500AR 500mAh NiCd
2 Banebots BB-12-45 ESCs GONE
2 12# bot drive ESCs, specs unremembered
ant electronics harness:
-2 scorpion minis GONE
-1 brushless Esskay outrunner
-1 brushless ESC for ^
-JST power connector
-microswitch
HandiWorks motor, 5/8" OD keyed adaptor.
modified handi motor with 1/2" output, heavily flat GONE
1 3-pound combot weapon blade, hardened S7, 3/8" Ti shaft, Al hub
small 3 3/8" carbide-tipped sawblade
antweight chassis and drivetrain:
-1/16" polycarbonate and standoffs chassis
-3.33:1 gearboxes, speed 400s, 4mm shafts
-2" wheels with adaptors for 4mm
-VERY FAST.
1 banebots 16mm gearhead motor, 24:1
1 banebots 16mm gearhead, 24:1
3 modified metal spur gearmotors, 20:1, 5mm output, with 2 mounts
3 copals, 60:1
1 swiss minimotor, 60:1, 3mm shaft
Chassis for beetleweight:
-1/8" carbon fiber base
-unhardened tool steel blade
-UHMW sidewalls
-1/16" polycarb top, unpictured
-Peligro-style
Beetleweight Guts Harnes: GONE
-Tekin Rebel ESC GONE
-2 heatsinked scorpion minis GONE
-2 banebots 25mm gearmotors, 20:1, drilled shafts for wheel attachment. GONE

This photo has notes. Move your mouse over the photo to see them.

Would you like to comment?

[?]

	vrogy's photostream
		2,937 uploads

Additional Information

Some rights reserved. This photo is public

Taken with a Digital Camera Vivicam.
More properties
Taken on January 25, 2005

Viewed 491 times

You	Sign in \| Create Your Free Account
Explore	Places \| Last 7 Days \| This Month \| Popular Tags \| Creative Commons \| Search
Help	Community Guidelines \| The Help Forum \| FAQ \| Sitemap \| Help by Email

Botstuff Cleanout Blowout Thing '07

Would you like to comment?

vrogy's photostream

Tags

Additional Information