Lubricator Housing and Parts

Lubricator Housing and Parts

Lubricator housing complete with some of the pump parts finished. I located the 0.25" and the 0-80...

Anyone can see this photo All rights reserved

Uploaded on Jan 15, 2012

2 comments

QCTP Handle

QCTP Handle

To position the hole for the handle shaft, I finger tightened the nut and marked the position.

Anyone can see this photo All rights reserved

Uploaded on Dec 31, 2011

0 comments

Nut and Wrench Combo

Nut and Wrench Combo

This is the Nut and Wrench that I am replacing. The wrench was just too large and it was easy to over...

Anyone can see this photo All rights reserved

Uploaded on Dec 31, 2011

0 comments

Fixture Front

Fixture Front

QCTP Nut is held firmly to 123 block with step clamp.

Anyone can see this photo All rights reserved

Uploaded on Dec 31, 2011

0 comments

Fixture Back

Fixture Back

123 block rests on 20 degree angle plate which is held in place by vise stop. 123 block is clamped by vise.

Anyone can see this photo All rights reserved

Uploaded on Dec 31, 2011

0 comments

Centering Curved Part

Centering Curved Part

This is a method that I use to locate the approximate center of a round piece. Sandwich a scale between...

Anyone can see this photo All rights reserved

Uploaded on Dec 31, 2011

0 comments

D1-5 Adapter Plate Rear

D1-5 Adapter Plate Rear

Adapter plates were purchased from Shars. I thought that the cast iron was good quality and they were machined well.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

3-Jaw Mounted

3-Jaw Mounted

These adapter plates took longer than I anticipated. I probably have 8-10 Hrs in each. Nothing is...

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

3-Jaw on Spacer

3-Jaw on Spacer

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

3-Jaw Adapter Back

3-Jaw Adapter Back

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Adapter Chuck Boss

Adapter Chuck Boss

This boss provides a close fit with the inside of the 3-jaw chuck.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

4-Jaw Mounted

4-Jaw Mounted

Most of the projects that I do are on a smaller scale, so the 4" 3-jaw and 4-jaw chucks seem better suited to hold the parts.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

4-Jaw Spacer Back

4-Jaw Spacer Back

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Chamfer Cut

Chamfer Cut

This face will be against the D1-5 Adapter

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Indicating for Chamfer

Indicating for Chamfer

The spacer was mounted to the adapter plate and the second side of the spacer was faced and a boss was...

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Holes Aligned

Holes Aligned

Fortunately, the holes in the spacer and the adapter plate lined up.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Better Rotary Table Clamp

Better Rotary Table Clamp

This is a better clamping method that I used on the second adapter plate. The previous method was tedious and time consuming.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

Tapping Adapter Plate

Tapping Adapter Plate

Drilled and Tapped for M8 x 1.25 in the adapter plate. The Adapter Plate was purchased from Shars.

Anyone can see this photo All rights reserved

Uploaded on Dec 29, 2011

0 comments

← prev 1 2 3 4 5 6 7 ... 27 28
(495 items)
Subscribe to a feed of stuff on this page... Subscribe to gregrycm's photostream – Latest | geoFeed | KML