|
Earl of Rossco's photostream |
|
Cat Converter: from above
CATCO converter as being used on my Stylus Kit Car. 3" in/out pipes, 4" thick &...
All rights reserved
Uploaded on Dec 26, 2007
Cat Converter: end view 02
Close-up of element - B2K I assume is the element type. Photo shows the free-flowing grid size,...
All rights reserved
Uploaded on Dec 26, 2007
Cat Converter: end view 01
End view of flange in wide angle -- pipe appears to be constricted. -- It is not. Pipe diameter is 3" parallel.
All rights reserved
Uploaded on Dec 26, 2007
Cat Converter: brand
Close-up of Brand. Stamping just above CATCO reads, NAT/CA D280-7 6500 And below reads MADE IN USA
All rights reserved
Uploaded on Dec 26, 2007
Exhaust System 004
Exhaust System 003
Polished Stainless Steel Exhaust box is 19.5" long by 4" diameter. From "Super Cat Motor-sport," Australia
All rights reserved
Uploaded on Dec 26, 2007
Exhaust System 002
The Cat Converter hanging under the floor. Will need some insulation between, plus a support hanger.
All rights reserved
Uploaded on Dec 26, 2007
Exhaust System 001
3" Dump pipe. I built it from 2 by ¼ turn of a "Do-nut" plus 3" pipe...
All rights reserved
Uploaded on Dec 26, 2007
Trailer - for Stylus carrying
12 x 6 -- double axle -- Ford 15" wheels -- brakes on front axle -- Hydraulic over-ride...
All rights reserved
Uploaded on Dec 3, 2007
Custom Intercooler on new front mount 02
Core is 45 x 30 x 7.5 cms. Turbo out pipe is 50mm & Throttle in pipe is 70mm Core is very...
All rights reserved
Uploaded on Dec 3, 2007
Custom Intercooler on new front mount 001
Core is 45 x 30 x 7.5 cms. Turbo out pipe is 50mm & Throttle in pipe is 70mm Core is very...
All rights reserved
Uploaded on Dec 3, 2007
Radiator-Fan Mount
Custom 22 x 17 copper radiator is 2" lower than original Aluminium Nissan unit & will fit...
All rights reserved
Uploaded on Dec 3, 2007
View-RHS Engine 0022
Shot shows fuel lines & brake lines fixed to chassis with insulated Alumin. "P"...
All rights reserved
Uploaded on Dec 3, 2007
View-Pedals and Pedal Box
Marine grade Aluminium Pedal box with Nissan units bolted on top
All rights reserved
Uploaded on Dec 3, 2007
Turbo Outlet Adaptor
Top rh corner pic shows original turbo outlet pointing up at about 70 degrees. Bottom rh pic is of...
All rights reserved
Uploaded on Dec 3, 2007
Tank, Fuel pump & pipes
Original MG Midget tank is far too small for Australian distances & not available anyway. Have...
All rights reserved
Uploaded on Dec 3, 2007
Tank Installed
Couple of earlier photos taken when the tank was first installed !!
All rights reserved
Uploaded on Dec 3, 2007
Intercooler Inlet
This cardboard, first version of the intercooler design had a very inefficient air flow direction:...
All rights reserved
Uploaded on Aug 18, 2007
1st Design C.B Intercooler
Mock-up cardboard intercooler In-Out pipes & ends changed as the air flow direction is rather...
All rights reserved
Uploaded on Aug 18, 2007
Final Alloy Intercooler
Intercooler sits 6 inches behind the opening. The in/out pipe angles were changed/raised to allow straighter pipe connections.
All rights reserved
Uploaded on Aug 18, 2007
12in Disk twin piston caliper
Custom 12 inch diam. slotted disk with original Escort 2 piston caliper --- which is mounted on a...
All rights reserved
Uploaded on Aug 18, 2007
12in Disk 15in Speedy Wheel
Note the 12" disc behind it, with original 2 pot Escort caliper. This wheel has screw-in...
All rights reserved
Uploaded on Aug 18, 2007
Excess Cables
Some of the original Nissan CA18 cables that need to be 'deleted'
All rights reserved
Uploaded on Aug 18, 2007
Construction // Stylus Kit Car
