761005-03 Thread an extra long screw into knob so it will stand up for finishing

761005-03 Thread an extra long screw into knob so it will stand up for finishing

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-02 Use tape to mark drill bit at depth per drawing-Drill at middle of flat spot

761005-02 Use tape to mark drill bit at depth per drawing-Drill at middle of flat spot

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-01 Hardwood Knob-Align grain-Sand half-inch diameter flat spot

761005-01 Hardwood Knob-Align grain-Sand half-inch diameter flat spot

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761000-01 Cable Clamp Bolt-Use hole in block-Drill just under head per drawing

761000-01 Cable Clamp Bolt-Use hole in block-Drill just under head per drawing

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-10 As needed file Side Rail slot so it allows full travel of Quadrant levers

761006-10 As needed file Side Rail slot so it allows full travel of Quadrant levers

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-03 Mark Side Rail at both ends of the Throttle Quadrant slot

761006-03 Mark Side Rail at both ends of the Throttle Quadrant slot

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-06 Align slot under Side Rail-Mark front end-Align on top-Mark center of holes

761006-06 Align slot under Side Rail-Mark front end-Align on top-Mark center of holes

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-11 Ready for cables-See Power Plant and Flight Controls for rigging

761006-11 Ready for cables-See Power Plant and Flight Controls for rigging

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-09 Insert bolt in first hole-Move clamp to opposite end and drill second hole

761006-09 Insert bolt in first hole-Move clamp to opposite end and drill second hole

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-05 Cut out notch in Side Rail using die grinder and cutoff wheel

761006-05 Cut out notch in Side Rail using die grinder and cutoff wheel

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-04 Set dividers to width of Quadrant slot-Transfer width to and Mark Side Rail

761006-04 Set dividers to width of Quadrant slot-Transfer width to and Mark Side Rail

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-02 Position Quadrant comfortable distance behind Instrument Panel

761006-02 Position Quadrant comfortable distance behind Instrument Panel

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761006-01 Clamp Quadrant on Side Rail-Used tape covered clamp

761006-01 Clamp Quadrant on Side Rail-Used tape covered clamp

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-07 Quadrant Assembly-Attach Knobs-Grease Friction Bearings-Bolt together

761005-07 Quadrant Assembly-Attach Knobs-Grease Friction Bearings-Bolt together

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-06 Watch for drips-Soak up with paper towel-Continue until finish is smooth

761005-06 Watch for drips-Soak up with paper towel-Continue until finish is smooth

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-05 When completely dry de-gloss with ScotchBrite-Clean with air-Dip again

761005-05 When completely dry de-gloss with ScotchBrite-Clean with air-Dip again

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761005-04 Dip the Knob into coating-Shake off excess-Stand up in hole in wood base

761005-04 Dip the Knob into coating-Shake off excess-Stand up in hole in wood base

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

761004-10 Remove template with solvent-Smooth and round edges-File inside curves

761004-10 Remove template with solvent-Smooth and round edges-File inside curves

Anyone can see this photo All rights reserved

Uploaded on Feb 15, 2012

0 comments

← prev 1 2 3 4 5 6 7 ... 952 953
(17,151 items)
Subscribe to a feed of stuff on this page... Subscribe to dbk4939's photostream – Latest | geoFeed | KML