CD Burning Error

CD Burning Error

K3B kept throwing an error about not having permission to access the device. After several iterations...

Anyone can see this photo All rights reserved

Uploaded on Jan 2, 2009

3 notes / 0 comments

dsc02142

dsc02142

First step: with scissors, cut the entire cord off right at the top of the stress reiever. Allow as...

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02143

dsc02143

Remove the seven screws from the back, and take off the front. Also remove the four screws holding the controller board in place.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

4 notes / 0 comments

dsc02144

dsc02144

left analog stick, and two screws

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02145

dsc02145

right analog stick and two screws.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02146

dsc02146

two other screws, which hold the memory card things in place. You don't have to take these out.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02147

dsc02147

Once the screws are out, you can stand the controller board up like so. No need to pull the vibrators...

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02148

dsc02148

Stress reliever and rubber cord. Also known as "trash".

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

0 comments

dsc02150

dsc02150

The memory card "slot". This should slide up and off easily once you have the stress reliever off.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

0 comments

dsc02152

dsc02152

Nicely, that big cable holder on the back comes off. Simply slide it down and off. Also trash.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02153

dsc02153

Strip the rubber shielding off the controller cable. Remove all the aluminum shielding, being VERY...

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02154

dsc02154

Okay, so there's still some shielding. I removed it later.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02155

dsc02155

Connect like-colored wires together, solder, and wrap in electric tape.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02157

dsc02157

One idea for a new internal arrangement. Didn't work, because there wasn't enough room below the memory card slot for the block.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

1 note / 0 comments

dsc02158

dsc02158

Using a roto-zip, dremmel, or some other tool that will do the job, remove much of the plastic from...

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02159

dsc02159

The "pincer" section widened. Bad pic, sorry.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

0 comments

dsc02160

dsc02160

This gives you a bit more of an idea what to do.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

2 notes / 0 comments

dsc02161

dsc02161

Wrap any exposed shielding or wires with electric tape, to avoid shorting out the board. Tuck the joints off to the side, just below the trigger.

Anyone can see this photo All rights reserved

Uploaded on Jul 28, 2008

4 notes / 0 comments

← prev 1 2 3 4 5 6 7
(124 items)
Subscribe to a feed of stuff on this page... Subscribe to eternicode's photostream – Latest | geoFeed | KML